Difference between revisions of "Raw sat"
Samneurohack (talk | contribs) |
Samneurohack (talk | contribs) (→Software) |
||
| Line 9: | Line 9: | ||
* Depending on your computer select the right serial port like : /dev/ttyUSB0, /dev/tty.usbserial (type ls /dev/ in a terminal) | * Depending on your computer select the right serial port like : /dev/ttyUSB0, /dev/tty.usbserial (type ls /dev/ in a terminal) | ||
* Setup 19200 baud and default 0D 0A line feed is fine. (Official Rock7 documentation is wrong !!) | * Setup 19200 baud and default 0D 0A line feed is fine. (Official Rock7 documentation is wrong !!) | ||
| + | * Repository for python style : [https://github.com/tmpbci/satmessenger here] | ||
You need to type "AT Commands" and the rockblock will answer like all modems. You can start with | You need to type "AT Commands" and the rockblock will answer like all modems. You can start with | ||
Revision as of 15:28, 11 September 2016
This page explain how to use Iridium satellite constellation for short burst data messages with a rockblock device.
You'll need to pay for the monthly fee (6 £) and buy credits to use this how to.
All text with these recipes will transfer without crypto. If you need crypto or a web interface, try Sat Messenger / RBS
Contents
- 1 Software
- 1.1 Send a message
- 1.2 Get Signal get 0-5 (rssi)
- 1.3 Get IMEI
- 1.4 Request system time
- 1.5 Manufacturer Identification
- 1.6 Model Identification
- 1.7 Revision
- 1.8 Geolocation Information
- 1.9 Ring status
- 1.10 RING status extended
- 1.11 RING mode query
- 1.12 Registration status
- 1.13 Initiate registration status
- 1.14 Read a Text Message
- 1.15 Remove Flow Control
- 1.16 Stock text message in buffer
- 1.17 Short Burst Data: Status
- 1.18 Short Burst Data: Status Extended
- 1.19 Trafic Management status
- 1.20 Short Burst Data: Gateway
- 1.21 Lock status
- 1.22 Initiate connection to satellite
- 1.23 Initiate connection and transfer either way
- 2 Rockblock +
Software
- See the hardware part to setup serial communication.
- Get serial communication software like coolterm or picocom.
- Depending on your computer select the right serial port like : /dev/ttyUSB0, /dev/tty.usbserial (type ls /dev/ in a terminal)
- Setup 19200 baud and default 0D 0A line feed is fine. (Official Rock7 documentation is wrong !!)
- Repository for python style : here
You need to type "AT Commands" and the rockblock will answer like all modems. You can start with AT The modem will answer : OK
Send a message
AT&K0
AT+SBDWT=Hello
AT+SBDIX
Get Signal get 0-5 (rssi)
AT+CSQ
Get IMEI
AT+GSN
Request system time
AT-MSSTM
answer is like : MSSTM: 2fbb7248
Manufacturer Identification
AT+GMI ou AT+CGMI
Model Identification
AT+GMM
Revision
AT+GMR ou AT+CGMR
Geolocation Information
AT-MSGEO
Answer is like -MSGEO: 4208,168,4772,2fa14b4d
Ring status
AT+CRIS
Answer is like +CRIS:000,000 (phone/fax,SBD)
RING status extended
AT+CRISX
Answer is like +CRISX:000,000,00000000 (phone/fax,SBD,timestamp)
RING mode query
AT+SBDMTA?
Registration status
AT+SBREG
Initiate registration status
AT+SBDREG?
0 Detached 1 Not registered 2 Registered 3 Registration denied
Read a Text Message
AT+SBDRT
Remove Flow Control
AT&K0
Stock text message in buffer
AT+SBDWT=Hello World
Short Burst Data: Status
AT+SBDS
like +SBDS: 1, 33, 0, -1
Short Burst Data: Status Extended
AT+SBDSX
- like +SBDSX: 1, 33, 0, -1, 0, 0
Trafic Management status
AT+SBDLOE
like +SBDLOE:0,0
Short Burst Data: Gateway
+SBDGW
EMSS ou non EMSS
Lock status
AT+CULK?
Initiate connection to satellite
AT+SBDI
+SBDI:<MO status>,<MOMSN>,<MT status>,<MTMSN>,<MT length>,<MT queued>
Initiate connection and transfer either way
AT+SBDIX
Rockblock +
IP 68 / 9-30V. You need :
- USB <-> serial DB9 adapter like a "Ugreen 2M USB 2.0 to Serial RS232 DB9 9Pin PL2303 Cable Adapter Converter".
