Ikos Pegasus reverse engineering

Device overview

• The rack with the power supply can hold up to 7 boards connected via a backplane.
• One main board with:
  • SCSI controller
  • 8051
  • CPLD
  • FPGAs
  • SDRAM
• 5 auxiliary boards with (each):
  • 1 XC95216 CPLD
  • 64 XC4036XL FPGAs
  • lots of SRAM
• One auxiliary board was destructively reverse engineered, so only 4 are remaining.

Some device photos are here.

Programming the auxiliary boards

Situation

In normal operation, the CPLD receives configuration data from the backplane (originating from the mainboard through the SCSI port) and distributes it to the FPGAs. The CPLD uses JTAG to send data to the FPGAs. The 64 FPGAs on each auxiliary board are arranged to form one big JTAG chain driven by the CPLD.

Because this mode of operation uses a proprietary protocol which is especially hard to reverse engineer since we do not have the original software and SCSI device driver, we are trying to program the boards with a JTAG probe.

CPLD access

The CPLD's JTAG port is accessible on each board with a HE10 connector following the MultiLINX pinout.

Vref	GND	NC	NC	NC	NC	NC	NC	NC
NC	TDO	NC	X	TDI	TCK	TMS	NC	NC

Legend: X = missing pin (key), NC = No Connect

We can use urJTAG to access the CPLD, with the BSDL files released by Xilinx to enable boundary scan. For an unknown reason, the Xilinx iMPACT tool fails to recognize the CPLD.

How to use boundary scan with urJTAG

 cable xpc_ext
 bsdl path [path to BSDL files]
 detect
 instruction EXTEST
 shift ir
 set signal [pin name from BSDL] out 1
 shift dr

FPGA JTAG chain topology

All the 64 FPGAs are arranged in a daisy chain for TDI and TDO.

For TCK and TMS, the board is divided into 4 quadrants and these signals are shared within each quadrant.

Connection of the FPGA JTAG chain to the CPLD

TCK and TMS are not directly connected to the CPLD, but go through a column of 74xx244 TTL buffers in the middle of the board. TDI and TDO are directly connected to the CPLD.

Signal	Quadrant	CPLD pin
TDI	All	96
TDO	All	92
TCK	Q1	88
TCK	Q2	TBD
TCK	Q3	TBD
TCK	Q4	90
TMS	Q1	115
TMS	Q2	TBD
TMS	Q3	TBD
TMS	Q4	TBD

LEDs

Each auxiliary board has 2 LEDs in the front. They are connected to CPLD pins 58 and 86 in current sink (active low) mode. They can be useful to test your CPLD boundary scan setup.

Design tools

Synthesis

You will need to use Synplify which supports the XC4000 family of FPGAs. There is no Xst support whatsoever.

Place and route

Synplify generates an EDIF netlist which can be fed to the ISE Classics tools for place and route and bitstream generation.

FPGA JTAG programming

TODO

• JTAG tunnelling through the CPLD boundary scan?
• or reprogram the CPLD to re-route JTAG somewhere else?
• does iMPACT support XC4000s?

Interconnect

The reverse engineering of the interconnect can be vastly automated by using techniques such as that of NSA@home.

FPGA to FPGA

TBD

FPGA to SRAM

TBD

FPGA to I/O port

TBD

Board to board

TBD